technical data sheet rpc-3.50 short circuit jack 03K12S-001D3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 1 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg all dimensions are in mm; tolerances according to iso 2768 m-h interface according to iec 60169-23 mechanically compatible with rpc-2.92 and sma documents application note an001 ?calibration services? material and plating connector parts material plating center conductor cube or equiv. gold, min. 1.27 m, over nickel outer conductor brass gold, min. 1.27 m, over nickel
technical data sheet rpc-3.50 short circuit jack 03K12S-001D3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 2 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg electrical data frequency range dc to 26.5 ghz return loss ? 0.10 db, dc to 4 ghz ? 0.12 db, 4 ghz to 8 ghz ? 0.20 db, 8 ghz to 26.5 ghz error from nominal phase 1 ? 1.0, dc to 4 ghz ? 1.5, 4 ghz to 8 ghz ? 2.0, 8 ghz to 26.5 ghz 1 the nominal phase is defined by the offset delay, the offset loss and the short inductance. mechanical data mating cycles ? 500 maximum torque 1.70 nm recommended torque 0.90 nm gauge 0.00 mm to 0.04 mm general standard definitions for proper operation the vector network analyzer (vna) needs a model describing the electrical behaviour of this calibration standard. the different models, units, and terms used will depend on the vna type and they will have to be entered into the vna. all val ues are based on typical geometry and plating. offset z o / impedance / z o 50 ? offset delay 16.6782 ps length (electrical) / offset length 5.00 mm offset loss 2.36 g ? /s loss 0.0111 db/ ghz short inductance 2 2 short inductances are determined indi vidually for each short circuit and are doc umented in a calibration certificate. environmental data operating temperature range 3 +20 c to +26 c rated temperature range of use 4 0 c to +50 c storage temperature range -40 c to +85 c rohs compliant 3 temperature range over which these specification are valid. 4 this range is underneath and above the operating temperature r ange, within the short circ uit is fully functional and could be used without damage.
technical data sheet rpc-3.50 short circuit jack 03K12S-001D3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 3 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg declaration of calibration options factory calibration standard delivery for this calibration standard includes a factory calibration. the calibration certificate issued reports individual calibration results, traceable to nat ional / international standards. model based standard definitions are individually optimized and reported in an agilent/keysight, rohde & schwarz and anritsu compatible vna format. accredited calibration optional this calibration standard can be delivered with an accredited calibration (dakks) having the highest confidence in the traceability. the dakks calibration ce rtificate issued reports indi vidual calibration results in a complex format, traceable to national / international standards. model based standard definitions are individually optimized and reported in an agilent/k eysight, rohde & schwarz and anritsu compatible vna format as well as in a dense data set needed for data based standard definitions. the uncertainties are smaller than in a factory calibration. for further, more detailed information see application note an001 on the rosenberger homepage. calibration interval recommendation 12 months packing standard 1 pce in box weight 6.95 g/pce draft date approved date rev. engineering change number name date herbert babinger 17.10.14 martin moder 17.10.14 c00 14-1492 herbert babinger 17.10.14 while the information has been carefully compiled to the best of our knowledge, nothing is int ended as representation or warran ty on our part and no statement herein shall be construed as recommendati on to infringe existing patents. in the effort to improve ou r products, we reserve the right to make changes judged to be necessary.
|
